Ellis Atlas AR2-A13 Cable Cleats
Ellis Cable Cleats
Single Cable Cleats
Cable Cleat Maximum Short Circuit Test Level 112kA – Cleat Spacing 750mm
Ellis AR2-A13 Atlas Cable Cleats are manufactured from galvanised or stainless steel and are ideal for single cable applications where the highest level of short circuit withstand are required – suitable for LV (Low Voltage), MV (Medium Voltage) and HV (High Voltage) power cable circuits.
Ellis Patents AR2-A13 cable cleats are suitable for securing single-way power cables between 47-55mm overall cable diameter – to protect and cushion LV-HV cables during short circuit conditions the Ellis Atlas cleat range is supplied integral with Low Smoke & Zero Halogen polymeric pads.
The cleats are available in a range of sizes with range taking ability to suit cables in single or trefoil formation.
Atlas Cable Cleats form part of the Ellis Patents range of single cable cleats – also available in galvanised or stainless steel Atlas trefoil cable cleats for cable diameters ranging from 24-102mm.
Ellis Cable Cleat AR2-A13
Technical Specification
- Cable Cleat Diameter Min 47mm
- Cable Cleat Diameter Max 55mm
Ellis AR2-A13 Atlas Cleat 47-55mm
Ellis patents AR2-A13 Cleat Dimensions
Two Bolt Cleat
- Width 170mm
- Height 140mm
- Cleat Depth 54mm
- P 150mm
- 2 x M 10 Cleat Fixing Holes
- Weight 940g
- Cable Cleat Order Code: AR2-A13-TB
Single Bolt Cleat
- Width 157mm
- Height 147mm
- Cleat Depth 54mm
- 1 x M 10 Cleat Fixing Holes
- Weight 940g
- Cable Cleat Order Code: AR2-A13-SB
Framing Channel
- Width 157mm
- Height 142mm
- Cleat Depth 54mm
- 1 x M 10 Cleat Fixing Holes
- Weight 940g
- Cable Cleat Order Code: AR2-A13-FC
Single Cable Cleat Selection Table
Specification details for Ellis Patents Atlas AR2-A13 cable cleat for single cable applications – the unique design of these cable cleats provides a choice of one bolt, two bolt or framing channel fixing options.
| Atlas Cable Cleat | Cable Dia Range (mm) | Cable Cleat Dimensions | Weight (g) | ||||||||||||
| Two Bolt | Single Bolt | Framing Channel | |||||||||||||
| W (mm) | H (mm) | C (mm) | P (mm) | Fixing Holes | W (mm) | H (mm) | C (mm) | Fixing Hole | W (mm) | H (mm) | C (mm) | Fixing Hole | |||
| AR2-A13-* | 47-55 | 170 | 140 | 54 | 150 | 2xM10 | 157 | 147 | 54 | 1xM10 | 157 | 142 | 54 | 1xM10 | 940 |
*Dimension ‘C’ is the cleat depth – not shown on drawing above. To order please add fixing suffix: Two Bolt-TB, Single Bolt-SB, Framing Cleat-FC
Ellis Atlas AR2-A13 Cable Cleats – Dimensions
Atlas Cable Cleats – Installation Instructions
Installation instructions for single way cables using Atlas cleats manufactured by Ellis Patents:
 |
 |
 |
 |
| 1. Position the cable clamp and fixing (not supplied) onto the support structure | 2. Install LV MV HV cable | 3. Locate the other half of the cable clamp. Secure with a nut and washer (not supplied) to the support structure and tighten the cable cleat | 4. IMPORTANT: Do not over tighten the cleat. The cleat should secure the cable but does not need to be so tight that the cable bulges at either side of the cleat |
WARNING – to prevent eddy currents and heating of the cable cleat the top tensioning bolt is made of stainless steel. Ensure that only this bolt is used and that bridging cannot take place. All Atlas cable cleats are supplied with two M12 nuts, bolts and washers.
See Ellis Patents for further details about cable cleats for LV-HV cable support and retention.
Ellis Atlas AR2-A13 Cable Cleats – Data SheetDownload
