Prysmian Telcleats are single piece, single fixing cable cleats manufactured from low density polythene providing cable support and protection against all weather conditions with operating temperatures -40°C to +60°C.
Prysmian Telcleats are part of the Prysmian Bicon range of cable cleats for cleating and clamping cables with diameters between 10mm to 51mm with low short circuit fault requirements.
Prysmian Telcleats Features & Benefits
- Suitable for supporting and cleating cables with outside diameters 10 to 51mm
- Telcleats manufactured from Low Density Polythene
- Sunlight (UV) and weather resistant for outdoor cable support
- Overlapping self-adjusting ranges
- Cable cleats can be double stacked on a single fixing installation
- Cable cleats tested in accordance with BS EN 50368
- See more information about BICON Cable Cleats
Telcleats are available as a single piece, single fixing design with a LUL approved LSOH LSF Afumex Telcleat range also available for rail cable clamps.
➡ Prysmian’s range of Afumex Telcleats are manufactured from LSOH polymer with one piece, single fixing cable cleats for 10-51mm cable diameters.
Prysmian Telcleats Performance Data
- Type – 6.1.2 Non-Metallic
- Impact Resistance – 6.2.4 Heavy -> 6.2.5 Very Heavy
- Lateral Load – 0.188 -> 0.775 kN
- Axial Load – 0.046 -> 1.118 kN
- Needle Flame – >60 Seconds
BS EN 50368:2003 Cable Cleats for Electrical Installations has been withdrawn and replaced by BS EN 61914:2009.
|Prysmian Telcleat Cable Cleat Selection||Prysmian Telcleat Cleat Details|
|Prysmian BICON Order Code||Cable Diameter||Standard Pack||Dimensions (mm)||Weight (g)||Roundhead Woodscrew||Screw Bolt|
|A (mm)||Cleat Quantities||B||C||D||Masonry, Concrete or Wood||For Cable Tray|
|Min||Max||Min||Max||Max||ins x No||mm|
|385AA01||10.5||14.5||100||15||18||32||12||2.3||1 1/4 x 8||M4 x 30|
|385AA02||12.2||16.7||100||17||22||36||14||3.4||1 1/2 x 8||M4 x 35|
|385AA03||14.6||19.8||100||21||26||43||16||5.5||1 3/4 x 8||M4 x 40|
|385AA04||17.7||24.0||50||25||31||51||18||8.6||2 x 8||M4 x 45|
|385AA05||21.7||28.5||25||30||37||57||20||12.4||2 1/4 x 12||M6 x 50|
|385AA06||26.2||34.2||25||35||43||65||22||16.4||2 1/2 x 12||M6 x 60|
|385AA07||31.9||41.6||10||42||52||78||25||24||2 3/4 x 12||M6 x 70|
|385AA08||39.3||51.1||10||50||62||91||26||35||3 1/4 x 12||M6 x 80|
Installing Prysmian Telcleats
Open the cable cleat and clamp around the cables so the end part of the cleat containing the slot will be in direct contact with the mounting surface – note all Prysmian Telcleats, except for BICON 385AA01, should be reversed to put the slot uppermost.
When mounting cable cleats directly channel section an adaptor (Prysmian 380AG**) must be used.
➡ For further information, specification and selection details about Prysmian Telcleats refer to the product sections below – see Prysmian Cable Cleats to view cable support clamps for LV, MV & HV cables including short-circuit protection for 11kV and 33kV cables.
Prysmian – mv hv 11kv 33KV CABLE ACCESSORIES
Prysmian manufacture the BICON range of electrical cable accessories including cable joints, terminations, glands and cleats to enable the installation of LV-HV power cables; contact T&D to discuss your 11kV-33kV requirements for jointing, terminating, cleating and glanding of medium voltage and high voltage cables.