3 Tonne LV-HV Power Cable Pulling Winch (Twin Capstan) SEB TCW3000

3 Tonne LV-HV Power Cable Pulling Winch (Twin Capstan) SEB TCW3000

3 Tonne LV-HV Power Cable Pulling Winch (Twin Capstan) SEB TCW3000

Cable Pulling Winch

SEB TCW3000 is a 3 tonne cable winch suitable for pulling LV-HV cables and is designed for simple, cost effective operation. The cable pulling winch is a fully enclosed steel canopied winch is extremely robust piece of engineering plant, designed specifically to cope with light/medium cable pulls and other general utility pulling.

SEB TCW3000 is suitable for pulling 11kV and 33kV power cables – contact T&D for the complete range of cable rollers, cable socks, conduit rods and underground cable protection.

3 Tonne LV-HV Power Cable Pulling Winch (Twin Capstan) SEB TCW3000

SEB TCW3000 Cable Winch

➡ Full range of HV Cable Joints & Cable Terminations also available.

3 Tonne Cable Winch (Twin Capstan)

SEB TCW3000 Cable Pulling Winch

Technical Specification

  • Payout (Approx.): 50mtrs/min
  • Line Pull: 12mtrs/min @ 3000Kgs
  • Rope Layering: Fully Automatic
  • Operating hour’s meter
  • 2 x Emergency Stop buttons (winch mounted)
  • 1 x Emergency Stop button on 5mtr cable (remote)
  • Digital rope meter counter
  • Digital line tension monitor
  • Line tension pre-set facility c/w controlled ramp down when set tension is achieved
  • 17.75Kw Lombardini Diesel Engine, Water Cooled
  • Demountable steel canopy for major servicing/repair
  • Rope capacity up to 1000mtr x 10mm diameter (Export Only)
  • Line speed is fully variable via console mounted control lever
  • Trench Boom (Optional Extra)
  • Winch recording facility c/w mounted printer & removable micro SD card, recording offers cable drum ID, time, length, line pull and setting of maximum overload and print out when that figure is reached (Optional Extra)
SEB TCW300 General Arrangement

SEB TCW300 General Arrangement

SEB TCW300 Parts List

  1. Hydraulic Motor
  2. Hydraulic Pump
  3. Hydraulic Oil Tank
  4. Diesel Engine
  5. Rewind Drum Hydraulic Motor
  6. Jockey Wheel
  7. Tow Coupling C/W Grease Point
  8. Rear Reaction Struts (Extendable)
  9. Digital Controller
  10. Mudwings
  11. Wheel & Tyre
  12. Rear Lights & Guards
  13. Emergency Stop
  14. Remote Emergency Stop / Stowage Box
  15. Diesel Tank C/W In Line Filter
  16. Lashing Points For Winch Anchorage
  17. Winch Lifting Shackles
  18. Canopy Lifting Eye Removable
  19. Sliding Inspection Panel For Layering Arm
  20. Engine Access Compartment
  21. Rewind Drum
  22. Control Console C/W Lockable Door
  23. Layering Arm Assembly
  24. Lift Off Canopy
  25. Stowage For Canopy Lifting Eye
  26. Rope Guide Assembly
  27. 12V Battery & Carrier
TCW3000 Procedure For Accessing Micro SD Card

TCW3000 Procedure For Accessing Micro SD Card

The Micro S.D card is fitted in the controller and stores all the recorded information which can readily be downloaded on a computer by using a card reader.

  • To access the card, unscrew the retaining bolt (Fig a) and lower down the hinged controller housing panel thus exposing the body of the controller unit
  • Lightly press the card (Fig b) to release it to the pop up position
  • Now carefully remove the card (Fig c) for downloading
  • Close and secure the hinged panel *

*Important Note!
Following removal or replacement of the S.D card immediately close and secure the hinged panel onto its rubber seal by lightly but firmly tightening the retaining bolt. Never leave the body of the controller exposed to the elements otherwise serious damage to electronics could occur.

Cable Winches

Cable Winches – complete range of winches to enable the pulling and installation of power (LV, MV & HV) and telecoms cables into cable trench or cable duct, including 11kV and 33kV medium voltages. See our complete range of Cable Pulling & Laying Equipment.