Euromold 400TE Tee Connector 11kV 33kV
Euromold 400TE is a screened separable tee connector specified to terminate and connect medium/high voltage cables onto Interface B bushings in the following voltage classes:
- 6/10 (12kV)
- 6.35/11 (12kV)
- 8.7/15 (17.5kV)
- 12/20 (24kV)
- 12.7/22 (24kV)
- 18/30 (36kV)
- 19/33 (36kV)
The Euromold 400TE tee connector with 400A current rating is designed for Interface B and covers voltages from 11kV/12kV to 33kV/36kV with a maximum conductor size of 185sqmm.
Euromold 400TE plug-in tee connectors can be supplied as an elbow connector (400LR) and plug-in type epoxy bushings – all suitable for use with Interface B type bushings on SF6 gas-insulated switchgear and medium/high voltage electrical equipment.
Euromold 400 Series MV HV Tee Connectors suitable for use up to 36kV 400Amps.
Designed to connect polymeric insulated cables (XLPE or EPR) with a copper wire screen but can be used on wire armoured, copper tape screen cables with the use of additional screen earth kits and accessories
Connector accessories include: dead-end receptacle, dead-end plug, stand-off plug and earthing plug for type B interfaces.
- Manufacturer – Nexans Euromold
- MV HV Equipment Bushing Connector – Interface B
- Maximum Operating Current – 400A (Amps)
- Voltage Classes – 12kV 24kV 36kV Maximum
- Terminate & Connect Cables – Polymeric XLPE EPR
- Conductor Cross Section Sizes – 25-240sqmm
- Applications – MV HV Switchgear, Transformers, Motors
âž¡ See complete range of Nexans Euromold ConnectorsÂ
EUROMOLD 400TE Specification
| Euromold separable connector type |
Voltage Um (kV) |
Current Ir (A) | Conductor sizes (sqmm) | |
| min | max | |||
| 400TE/G | 11kV | 400 Amps | 70 | 240 |
| K400TE/G | 24kV | 400 Amps | 25 | 240 |
| M400TE/G | 36kV | 400 Amps | 35 | 185 |
Euromold 400TE Tee Connector 11kV 33kV – Design
Separable elbow connector comprising:
- Conductive EPDM insert
- Conductive EPDM jacket
- Insulating EPDM layer moulded between the insert and the jacket
- Type B – 400 A interface as described by CENELEC EN 50180 and 50181
- Conductor connector
- Basic insulating plug (with VD point)
- Cable reducer
- Conductive rubber cap
- Clamping pin contact
- Bail restraint
- Earthing lead
The thick conductive EPDM jacket provides a safe to touch screen which ensures safety for personnel, cables and electrical equipment in medium/high voltage installations.
Euromold 400TE Selection Table
For Screened MV HV TEE Connectors
Select the Euromold ordering part number which positions the cable most central to the minimum and maximum core insulation diameter, then substitute X using the table below. Add a ‘K’ for use up to 24 kV and add an ‘M’ for use up to 36 kV.
The complete Euromold 400TE tee connector kit comprises the following components – cable lubricant, wipers, installation instructions and crimp chart.
Kit Contents for Euromold 400TE Connectors
| Euromold 400TE Connector Part Number |
Dia. over core insulation (mm) | |
| min | max | |
| 400TE/G-11-X | 12.0 | 17.5 |
| 400TE/G-15-X | 16.0 | 22.0 |
| 400TE/G-19-X | 20.0 | 26.5 |
| 400TE/G-22-X | 23.5 | 31.0 |
| 400TE/G-25-X | 26.5 | 32.5 |
| 400TE/G-27-X | 28.5 | 37.5 |
| Conductor sizes (sqmm) |
Aluminium Cables | Copper Cables | |
| DIN Hexagonal Crimp | Deep Indent Crimp | DIN Hexagonal Crimp | |
| 25sqmm | – | – | 25(K)M-11-2 |
| 35sqmm | 35(K)M-12-2 | 35KM-12-1 | 35(K)M-11-2 |
| 50sqmm | 50(K)M-12-2 | 50(K)M-12-1 | 50(K)M-11-2 |
| 70sqmm | 70(K)M-12-2 | 70(K)M-12-1 | 70(K)M-11-2 |
| 95sqmm | 95(K)M-12-2 | 95(K)M-12-1 | 95(K)M-11-2 |
| 120sqmm | 120(K)M-12-2 | 120(K)M-12-1 | 120(K)M-11-2 |
| 150sqmm | 150(K)M-12-2 | 150(K)M-12-1 | 150(K)M-11-2 |
| 185sqmm | 185(K)M-12-2 | 185(K)M-12-1 | 185(K)M-11-2 |
| 240sqmm | 240(K)M-12-2 | 240(K)M-12-1 | 240(K)M-11-2 |
Euromold MV HV | Cable Terminations, Connectors, Elbows & Joints
Euromold | Connect | Joint | Terminate MV HV Cables – view our complete range of HV Joints & Terminations in heat shrink, cold shrink, push-on and plug-in versions.
Nexans Euromold Connectors Interface BDownload
