Ellis VRT+19 Vulcan Trefoil Cleats (LV MV 11kV 33kV HV)

Ellis VRT+19 Vulcan Trefoil Cleats (LV MV 11kV 33kV HV)

Ellis Cable Cleats

Trefoil Cable Cleats

Cable Cleat Maximum Short Circuit Test Level 104/132kA – Cleat Spacing 600/300mm

Ellis VRT+19 Vulcan+ Cable Cleats are manufactured by Ellis Patents from corrosion resistant stainless steel for LV (Low Voltage), MV (Medium Voltage) and HV (High Voltage) power cable circuits – the compact cleat design is suitable for clamping industrial LV-HV power cables including 11kV and 33kV cables depending on short-circuit calculations according to IEC61914 calculations.

Ellis Patents VRT+19 cable cleats are suitable for securing trefoil power cables between 89-97mm overall cable diameter.

The NEW Twist Foot Design from Ellis Patents provides reduced installation times and labour savings when installing cable cleats.

The cleats are available in a range of sizes with range taking ability to suit cables in single way or trefoil formation. 

Vulcan Cable Cleats form part of the Ellis Patents range of trefoil cable cleats – also available in stainless steel Vulcan+ single way cable cleats for cable diameters ranging from 30-110mm.

Ellis VRT+19 Vulcan

Trefoil Cable Cleats

  • Cable Cleat Diameter Min 89mm
  • Cable Cleat Diameter Max 97mm

Vulcan cable cleats are available for single, trefoil, quad and bundled cable installations.

Ellis VRT+19 Vulcan Trefoil Cleats (LV MV 11kV 33kV HV)

Ellis VRT+19 Vulcan Trefoil Cleats 89-97mm

Ellis patents vulcan VRT+19 Cleat Dimensions

  • Width 200mm
  • Height 235mm
  • Depth 54mm
  • P 75mm
  • Base Holes 3 x M10
  • Weight 637g

Trefoil Cable Cleat Selection Table

Specification details for Ellis Patents Vulcan VRT+19 cable cleat for trefoil cable applications:

Vulcan+ Cable Cleat Part Number Trefoil Cable Range Dimensions Weight (g)
Min Dia (mm) Max Dia (mm) W (Max) (mm) H (Max) (mm) D (mm) P (mm) Base Holes
VRT+19 89 97 200 235 54 75 3 x M10 637

 

Ellis VRT+19 Vulcan Trefoil Cleats (LV MV 11kV 33kV HV)

Ellis Patents Vulcan+ Stainless Steel Trefoil Cable – Dimensions

Vulcan+ Cable Cleats – Installation Instructions

Installation instructions for trefoil cable cleats using Vulcan+ cleats manufactured by Ellis Patents:

Bolt the cleat to the support structure using either the single central or two outer fixing positions Install the cables, when necessary remove the removable base pad to allow for the larger cables in the cleats range Remove the flange nut. Bend the two edges of the cleat around the cables until they are parallel. Locate the screw into adjacent hole and replace the flange nut Tighten Flange Nut
1. Bolt the cable  cleat to the support structure using either the single central or two outer fixing positions 2. Install the cables, when necessary remove the removable base pad to allow for the larger cables in the trefoil cleats range 3. Remove the flange nut. Bend the two edges of the cleat around the cables until they are parallel. Locate the screw into adjacent hole and replace the flange nut 4. Tighten flange nut

WARNING – Do not over tighten the cable cleat. The liner should be in good firm contact with the cable but does not need to be so tight that the cable bulges at either side of the liner.

Ellis Patents Cable Cleats

Ellis Cleats | Emperor | Vulcan | Atlas | Phoenix | Single Trefoil Bundled Cables

Data Sheets