Duct Seals

Sealing Cables, Switch Hall & Grid Transformer Bases On 132kV Wind Farm

• Product Category: Duct Seals
• Application:Sealing Extra High Voltage Cables & Ducts Against Water, Gas & Fire
• Voltage: High Voltage 132kV
• Sector: Renewable Energy (Wind)
• Product Installed: Filoseal+, Filoseal+HD and Filoseal+ HD Fire Cable Duct Sealing System
• Project Information: All 3 types of Filoseal cable duct seal systems were required; original Filoseal+ with foam backing, newer Filoseal+HD for heavier cables and the newest seal type Filoseal+HD FIRE which adds BS EN1366 Part 3 with up to 4 hours of fire protection. All four cable duct seals were installed according to instructions whilst special guidance and tips were given on site by the manufacturer
• See Also: Cable Transits

Duct Seals

Thorne & Derrick International

Since 1985 Thorne & Derrick based in the UK have been specialist distributors of LV, MV & HV Cable Installation, Jointing, Substation, Arc Flash Clothing & Electrical Safety Equipment – customers include UK and worldwide contractors, specifiers, traders and end-users involved in medium and high voltage cable installations, cable jointing, substation, overhead line and electrical construction.

We are specialist stockists and distributors of 11kV-33kV Cable Joints, Terminations & Connectors from manufacturers including 3M, Pfisterer, Prysmian and Nexans Euromold in a selection of cable jointing technologies including push-on, heat shrink and cold shrink joints and cold shrink terminations.

♦ 132kV Surge Arresters | 132kV Link Box Stockists

MV HV | Medium & High Voltage Power Products, Tools, Cables & Electrical Equipment

Rat & Rodent Resistant Cable Duct Seals For LV MV HV Cables & Substations

• by Chris Dodds T&D - estimated reading time 3 minutes

Sealing Ducts

Wildlife induced power outages are increasingly caused by the invasion of rats and rodents into medium/high voltage electricity substations via unsealed and inadequately sealed cable ducts and then gnawing electricity power cables.

Filoform FiloSeal+HD is a duct sealing system that is able to seal large heavy armoured power (multicore XLPE SWA) and high voltage cables in ducts, bore holes or cable transit frames – providing a strong support system using hexagonal tubes building a re-enterable seal with honeycomb structure.

The duct seal system is extensively approved and used by UK utilities, DNO’s and their preferred ICP (Independent Connection Provider) to protect electrical assets and cables within substations typically operating at 11kV, 33kV, 66kV and up to 132kV from rat attack.

The cable duct seal kits have been extensively tested against pressure, pulling forces, chemicals, gases and hydrocarbons for adequate sealing of LV-HV cables against the danger of flood (water ingress) or gas migration.

Recently, testing was carried out to establish the ability of the duct seal system to resist, repel or prevent rat attack through cable ducts into electricity substations and the following post provides information about the test and their conclusions.

TalkTalk suffered a major outage caused by rodent damage to fibre optic cables in 2017.

Sealing Cables & Ducts

Rat & Rodent Testing

Filoform have carried out tests to assess the physical damage caused to the FiloSeal+HD cable sealing sealant by a group of four rats (two males and two females) which are given free access to the duct seal for a period of four weeks.

The FiloSeal+HD comprises of MD+ sealant with hexagonal tubes as the backing product which was positioned within a metal tube.

Each end of the tube was sealed with 25mm of MD+ sealant ensuring that access to the backing product could only be achieved by significant damage to the MD+ sealant.

This tube was mounted in the center of the cage and consequently, the male and female sides of the cage had access to opposite ends of the tube.

Test cage before start of study

Immediately before rats placed in cage – side exposed to males	Immediately before rats placed in cage – side exposed to females
After one week of exposure – side exposed to males	After one week of exposure – side exposed to females
After four weeks of exposure – side exposed to males	After four weeks of exposure – side exposed to females

Duct Seals | Substations

Conclusion

The results at the end of the four week study indicated that there was no apparent difference in the damage caused by the male rats in comparison to the female rats and though the damage increased over the duration of the study the MD+ duct sealant was not penetrated by the rats and the hexagonal backing tubes were not exposed or damaged.

No abnormalities, ill health or behavioural changes occurred to the rats during the study and all four rats achieved satisfactory body weight gain during the exposure period.

Several hard red pieces were observed in the large intestines of one female and in the stomach of one male and one female. There were no other abnormalities observed at the post mortem macroscopic examination at study termination on Day 29.

In conclusion as the hexagonal tubes were not damaged after 4 weeks of exposure with direct access, therefore, it is reasonable to assume that different backing products will be protected to a similar degree, when enclosed by MD+ cable duct sealant.

THORNE & DERRICK are national distributors LV, MV & HV Cable Installation, Jointing, Substation & Electrical Equipment – we service UK and global businesses involved in cable installations, cable jointing, substation, overhead line and electrical construction at LV, 11kV, 33kV and EHV.

Since 1985, T&D have established an international reputation based on SERVICE | INTEGRITY | TRUST.

Contact us for 3M Electrical, ABB, Alroc, AN Wallis, CATU Electrical, Cembre, Centriforce, CMP, CSD, Elastimold, Ellis Patents, Emtelle, Euromold, Filoform , Furse, Lucy Electric & Zodion, Nexans, Pfisterer, Polypipe, Prysmian, Roxtec, Sicame, WT Henley.

Invitation

Thorne & Derrick invite you to join LinkedIn’s largest LV-HV Electrical Discussion Group : Low & High Voltage Power, Cabling, Jointing & Electricals. Discussion subjects include cable installations, cable jointing, substation, overhead line and electrical construction at LV, 11kV, 33kV and EHV. Network, engage and promote your profile, company or products with over 10,000 influencers.

Duct Seals – Sealing Cable Ducts Containing Low Voltage Control Cables

• Product Category: Duct Seals
• Application: Sealing Cable Ducts Containing LV Control Cables (Flexible & Insulated)
• Voltage: Low Voltage 600/100V
• Sector: Cold Rooms For Food Production & Storage
• Product Installed: Filoseal+HD Cable Duct Sealing System
• Project Information: The Filoseal cable duct seal system was selected to seal 50mm and 110mm outside diameter cable ducts to provide up to 2 bar Pressure Resistance and prevent water ingress into the low voltage control rooms effecting sensitive electronic and electrical equipment.
• See Also: Cable Transits

Refrigerant Plant Control Wiring

Duct Seals

Thorne & Derrick International

Since 1985 Thorne & Derrick based in the UK have been specialist distributors of LV, MV & HV Cable Installation, Jointing, Substation, Arc Flash Clothing & Electrical Safety Equipment – customers include UK and worldwide contractors, specifiers, traders and end-users involved in medium and high voltage cable installations, cable jointing, substation, overhead line and electrical construction.

We are specialist stockists and distributors of 11kV-33kV Cable Joints, Terminations & Connectors from manufacturers including 3M, Pfisterer, Prysmian and Nexans Euromold in a selection of cable jointing technologies including push-on, heat shrink and cold shrink joints and cold shrink terminations.

MV HV | Medium & High Voltage Power Products, Tools, Cables & Electrical Equipment

Sealing Cable Ducts Containing Multiple Single Core Cables In A Data Centre

Sealing Cable Ducts

• Guest Blog: Steve Groocock (Duct Seal Products – Account Manager at Filoform UK)
• Product Category: Cable Duct Sealing

Filoform FiloSeal +HD is a duct sealing system specified to protect and seal larger heavy armoured power and high voltage cables in LV, MV & HV substation ducts, bore holes or transit frames – the duct seal provides a strong support and cable sealing system using hexagonal tubes building a re-enterable honeycomb structure to resist water, gas and fire.

Re-enterable cable duct seals are easy to apply regardless of the type of cable scenario in the cable ducts as it uses a strong but flexible hexagonal tube structure to support the cable and provide a strong backing for the cable seal.

The duct seal system provides waterproof and gastight sealing of LV-HV and 11kV-33kV power cables into ducts. The FiloSeal+HD is suitable for any cable configuration (single, trefoil cables or multiple cables) contained within one duct and also allows for easy re-entry of the duct seal to add or remove cables or pipes as required.

Filoform Filoseal+HD is covered by a Test Report documenting successful pass status at Nedlab Laboratory for the following – this is based upon using Filoform’s hexagonal support system and sealing cable using their MD+ sealant.

• Pressure Test, Bending Test & Pull Strength
• Resistance Test Against Chlorine, Methane Gas & Chemicals In Hazardous Areas
• Resistance Test Against Hydrogen Sulphide Gas
• Resistance To Onshore & Offshore Hydrocarbons

FiloSeal+HD Cable Duct Seals – Honeycomb Structure

Duct Sealing

Installing & Preparing The Cable Seal

Steve Groocock is the Duct Seal Product Manager at Filoform. Below he explains about attending a data centre site where he provided installer training prior to the installation of Filoseal +HD Re-enterable Duct Seal System.

“A skill is something that is learned over a period of time but sometimes it is best to pass along experience to a new user of any equipment, this includes cable duct seals. Recently, I attended site for a company who were working on the LV cabling associated with a new build data centre into an existing building structure.

The LV cable, ducting and electrical distribution system utilised existing switch rooms where possible but in order to add capacity to these areas, new penetration holes for the cabling needed to be added. These holes were core drilled directly through the existing structure. Once the cables had been pulled, there remained clear passages for the ingress of moisture, gas, dust and rodents into cable ducts.

Taking the strips of adjoined hex tubes, insert them around and between the cables to be sealed ensuring the spacing required is maintained – the strips can be inserted as a flat line or rolled to form a tight group of 5. If space is not available, the strip of hex tubes may be torn down to individual hex tubes.

Start at the bottom of the cable duct with the large blue tubes and build up to completion. Should there be heavy cables in the ducts, such as 11kV/33kV high voltage power cables, the hex tubes can be nested i.e. one small tube placed inside the other larger tube. The small light blue hex tubes are used to fill and seal the remaining small gaps in the cable duct. The installer should ensure the tubes are packed tightly to prevent cable movement.

Filoseal+HD duct sealing kits have been tested to provide watertight, gastight and/or fire resistant cable seals and were thus specified to fill in the voids in the concrete core drilled holes at the data centre.

Training took two hours and in this time it was up to me to pass on as much experience as possible at a steady pace so the new installer could take it understand and adopt the knowledge. The installer had previously not seen a duct sealing system like this so I took time to familiarise them with the component parts and how a finished cable duct seal installation should look like by way of a sample in a clear duct replica. I also showed the excellent Filoform HD installation video which can be viewed below.

The hands on training starts with myself and the trainee cleaning and abrading the cables and cable duct for the first 20-25mm inside the hole in the wall – cleaning cloth is provided with the duct seal kit. Preparation is key to the whole system – the most important point I stressed to achieve a hexagonal backing piece between each and every cable to create a reliable water and gastight cable duct seal.

The hexagonal tubes are placed around the cables to be sealed filling up all the gaps using the large and small hexagonal backers to ensure the cable support system is compact and tight resembling a honeycomb structure.

This is explained in the Video and instructions supplied with the duct seal kit but until seen it is not necessarily clear as to why. The space is there to ensure the duct sealant component, called Filoseal MD+, can reach all the areas of the void or cable duct needed to be sealed. This site was particularly challenging as the low voltage cables were held down close and clamped to the work face by cable cleats. However, I moved to the other side of the wall and moved the cables in a pit until my trainee could get the hexagonal pieces between each and every cable and between the cables and the core drilled hole edge.

Here the cables are pictured clamped to the cable channel using trefoil cable cleats as the cables depart the duct which was sealed using Fioloseal type duct sealing mastics.

This is the end of stage one. Once we both looked and examined the backing ensuring there were gaps around the cables to be sealed as specified, we moved on to the addition of the sealing mastic. The cable sealing mastic can be applied using a standard mastic gun, however we recommend investment in a quality installation gun. Once the sealant mastic is loaded in the gun I demonstrated on the lower half of this cable install how to ensure a cable seal by running a good bead around the hole edge on every cable. Once we had gone through several tubes of mastic we brought out the finishing sponge to wipe down and tidy the mastic finish – the duct sealant can take from 4 to 20 days to fully cure depending on local ambient temperatures and air humidity levels. Typically in the UK curing takes 8-20 days and backfilling of the installation should be avoided until at least 10 days after installation.

When backfilling ensure adequate packing is below the sealed cables in the duct before adding materials above the cables. In a vertical cable duct, group together strips or rolled groups of tubes and squeeze them into the a duct as one single unit.

Then proceed to maintain the required cable spacing by adding either large or small tubes (groups of or singly).

Duct Sealing – Preparation Is Key

The mastic should be patted in and around every cable ensuring each and every part of the cable duct seal was treated the same way – this patting motion encourages the cable sealant mastic to adhere to the hexagonal backing. Final checks led me to further pat parts between cables using the sponge edge.”

Cable Duct Seal Selection Table

Fire Resistant Duct Seals

Duct seals suitable for LV-HV power cables in single, trefoil or multiple configurations, including 11kV Triplex and 33kV high voltages

Provides advanced and assured sealing against water and gas for cable ducts, bore holes and openings

Re-enterable sealing system future-proofed for retrofit of new cables or re-routing of existing through cable ducting

Cable duct seals provide protection of substations and basements against flood, fire and gas ingress dangers

Conclusion

Filoseal+HD duct seal system using MD+ has been heavily tested against pressure, pulling forces, chemicals, gases and hydrocarbons for use with low, medium and high voltage cables. Below we can summarise the results from Nedlab Laboratory Test Reports.

Final Pressure Test – after completion of the bending and pull strength test the cable duct seals are tested at a pressure of 2.0 Bars.

Note the Test Results documented above have been done in accordance with Filoform installation instructions, however values achieved in field installations can vary if the instructions are not followed and results may vary depending on cable and duct tolerances such as cable duct size, material and cable density volume.

Further reading:

• Trefoil Cables – Sealing Ducts & Cleating Trefoil Cables Up To 33kV 
• Sealing Cable Ducts In Hazardous Areas According To ATEX Directive

THORNE & DERRICK are national distributors LV, MV & HV Cable Installation, Jointing, Substation & Electrical Equipment – we service UK and global businesses involved in cable installations, duct sealing, cable jointing, substation, overhead line and electrical construction at LV, 11kV, 33kV and EHV.

Since 1985, T&D have established an international reputation based on SERVICE | INTEGRITY | TRUST.

Contact us for 3M Electrical, ABB, Alroc, AN Wallis, CATU Electrical, Cembre, Centriforce, CMP, CSD, Elastimold, Ellis Patents, Emtelle, Euromold, Filoform , Furse, Lucy Electric & Zodion, Nexans, Pfisterer, Polypipe, Prysmian, Roxtec, Sicame, WT Henley.Invitation: Thorne & Derrick invite you to join LinkedIn’s largest LV-HV Electrical Discussion Group : Low & High Voltage Power, Cabling, Jointing & Electricals. Discussion subjects include cable installations, cable jointing, substation, overhead line and electrical construction at LV, 11kV, 33kV and EHV. Network, engage and promote your profile, company or products with over 10,000 influencers.

Trefoil Cables – Sealing Ducts & Cleating Trefoil Cables Up To 33kV

by Chris Dodds T&D - estimated reading time 5 minutes

Trefoil Cables

Before we demonstrate an effective duct seal solution for trefoil cables let us first define trefoil and cover the importance of selecting correct cable cleats to prevent short-circuit inflicted damage to power systems and electrical infrastructure.

Cable installations for 3 phase power installations, whether LV or MV (600/1000 Volts to 11kV/33kV) utilise single conductor cables typically in flat or trefoil cables formation – trefoil cable cleats are used to restrain 3 single core cables installed in the “shamrock” style formation, commonly referred to as trefoil.

Where a 3 phase cable system design is based on trefoil cables formation The 17th Edition Wiring Regulations (BS7671) can be consulted to provide current ratings and voltage drop values for the installation.

Trefoil cable formation refers to the installed method for low, medium and high voltage power cables where three single core (phases) distribute the electricity supply rather than a single 3 core cable cable.

Typically, at low voltage (LV) this would be single core XLPE/AWA armoured power BS5467 cables or at medium/high voltage (11kV/33kV) polymeric (XLPE or EPR insulated) single core BS6622 cables.

See more information about Trefoil Cleats

MV HV Single Core – 11kV Single Core Conductor Cables BS6622

Depending upon the short circuit calculation according to IEC 61914 the appropriately fault-rated cable cleats should be used to provide cable restraint depending on whether the LV, MV or HV power cable system generates short, medium or high short circuit levels.

According to the installation application and environmental conditions trefoil cleats are available in a selection of materials including nylon, stainless steel and aluminium.

View the complete range: Ellis Patents Cable Cleats

Clearly cleating cables is essential, as is effective sealing of cable ducts to prevent flood damage to substations and buildings or the spread of potentially flammable gases.

Sealing Trefoil Cables In Substation Ducts

Single core 11kV-33kV cables in “triplex formation” according to British Standard BS7870 require effective sealing of cable duct entries against water, gas and fire on medium/high voltage substations as well as cleating to protect against short circuit situations. Triplex cables are characterised by the appearance of 3 core cables twisted around each other.

MV HV Triplex – 11kV Triplex Cables 3 Core Conductor Cables BS7870

Trefoil cable arrangements entering substation ducts can be difficult to seal using traditional mastic or inflatable cable duct sealing systems, however the FiloSeal+HD duct sealing system effectively seals single, trefoil or multiple cables in duct. The single core cables are carefully separated and supported using the FiloSeal+HD hexagonal tubes – note the central positioning of the hexagonal tubes to establish the required HV cable separation and allow maximum flow of the duct sealant into the trefoil cable formation.

The hexagons separating the pictured 11kV cables must have the smaller hexagonal tubes nested in the large one to create additional strength.

Sealing Cable Ducts With Single, Trefoil & Multiple Cables | LV MV HV 11kV 33kV

Where the cable ducts are located in a designated hazardous area according to the ATEX Directive we can provide expert advice and product recommendations for sealing cables in potentially explosive atmospheres.

Filoform  – Water, Gas & Fire Protection | Duct Seals In Industrial & Hazardous Areas

Should you require any advice to enable to selection of duct seals for industrial or hazardous area locations, call us | LV MV HV | 11kV 33kV Cable Joints & Terminations

Thorne & Derrick International

Since 1985 Thorne & Derrick based in the UK have been specialist distributors of LV, MV & HV Cable Installation, Jointing, Substation, Arc Flash Clothing & Electrical Safety Equipment – customers include UK and worldwide contractors, specifiers, traders and end-users involved in cable installations, cable jointing, substation, overhead line and electrical construction at Low, Medium & High Voltages.

We are specialist stockists and distributors of 11kV-33kV Cable Joints, Terminations & Connectors from manufacturers including 3M, Pfisterer, Prysmian and Nexans Euromold in a selection of jointing technologies including heat shrink, cold shrink and push-on.

MV HV | Medium & High Voltage Power Products, Tools, Cables & Electrical Equipment