Blog

G81 ENA Engineering Recommendation – 11kV 33kV 66kV Joints, Terminations & Connectors WPD

• uploaded by Chris Dodds - Thorne & Derrick Sales & Marketing Manager

G81

The following materials framework according to ENA Engineering Recommendation G81 Part 5 “Framework for Materials Specification for Industrial & Commercial Underground Connected Loads Up To & Including 11kV” includes the approved Cable Joints, Terminations & Connectors approved for use with HV Switchgear, HV/LV Transformers & Substations on the Western Power Distribution (WPD) network.

Should you require any technical support or have any commercial requirements about G81 Approved 11kV/33kV Cables & Accessories please do not hesitate to contact Thorne & Derrick Sales Team.

Cable Joints for Medium & High Voltage Cables | the Lovink range of cable joints provide high-performance for high-challenge applications including configurations for straight, transition, branch and loop jointing of cables typically distributing electricity at 11kV, 24kV and 33kV; this includes connection joints for extensions and repairs for MV HV cables with XLPE, PILC & EPR insulation.

The Lovisil range of water proof cable joints provide excellent continued service for Medium & High Voltage Cables in flooded cable trenches, underground cable ducts and general wet-conditions associated with high-water table applications with a Type-Test documented to 2 Bar water pressure; typically used to fault repair, divert and extend single and 3-core cables with XLPE, EPR and PILC insulation with 11kV 24kV 33kV voltage classification.

WPD

List Of Approved Materials & Suppliers 11kV 33kV 66kV

Thorne & Derrick International

T&D distribute the most extensive range of MV & HV Jointing & Terminating, Installation & Cable Pulling Equipment – we service UK and international clients working on underground cables, overhead lines, substations and electrical construction at LV, 11kV, 33kV and EHV transmission and distribution voltages.

• Key Products: MV-HV Cable Joints & Terminations, Cable Cleats, Sealing Cable Ducts, Cable Transits, Underground Cable Protection, Cable Jointing Tools, Feeder Pillars, Cable Ducting, Copper Earthing, Electrical Safety, Cable Glands, Arc Flash Protection & Fusegear.

• Distributors for: 3M, ABB, Alroc, Band-It, Catu, Cembre, Centriforce, CMP, Elastimold, Ellis Patents, Emtelle, Furse, Lucy Zodion, Nexans Euromold, Pfisterer, Polypipe, Prysmian, Roxtec.

Read Our Blog: The Next Generation Of 11kV Transformers For MV HV Networks

Switchgear Cable Terminations

T&D distribute MV-HV Switchgear Cable Terminations to suit 11kV/33kV connections into air, oil and gas insulated switchgear or transformers including heat shrink, cold shrink and separable connectors for both inner cone and outer cone bushings from leading manufacturers including Nexans Euromold, 3M and Pfisterer.

♦ See more: Heat Shrink Cable Terminations 11kV 33kV | Cold Shrink Cable Terminations 11kV 33KV

MV HV – Medium & High Voltage Cable Joints, Terminations & Connectors (11kV 33kV EHV)

More…

T&D’s Power Blog covers: LV MV HV & EHV Transmission & Distribution, Substations, Switchgear, Cable Jointing & Termination, Cable Fault & Repair, Underground Cables.

➡ Visit Power Blog.

11kV Pot End Live Cable End Seal | 11kV Cables Single Core XLPE CWS

Cable Abandonment | Pot End Cable End Seals | Energised or Dead Cables 11kV

Complete range of cable abandonment kits and live pot end sealing kits for : 11kV HV High Voltage Cables Single Core XLPE CWS.

Kits also available for: 11kV HV High Voltage Cables 3 Core XLPE EPR Cables.

For 600/100V power cable systems see Live Pot End Kits for LV power systems.

➡ Joints | Terminations 11kV 33kV Heat Shrink

11kV

Installation Video: High Voltage Pot End Live Cable End Seals 

11kV Pot End Live Cable End Seal | 11kV Cables 3 Core XLPE EPR

Cable Abandonment | Pot End Cable End Seals | Energised or Dead Cables 11kV

Complete range of cable abandonment kits and live pot end sealing kits for : 11kV HV High Voltage Cables 3 Core XLPE EPR.

Suitable to provide 11kV Pot End Sealing of all types of 3 core polymeric insulated cables XLPE/EPR with copper tape screen and wire braid (PSWB GSWB) or wire armour (SWA).

For 600/100V power cable systems see Live Pot End Kits for LV power systems.

Kits also available for: 11kV HV High Voltage Cables Single Core XLPE CWS (Copper Wire Screened).

➡ Joints | Terminations 11kV 33kV Heat Shrink

11kV

Installation Video: High Voltage Pot End Live Cable End Seals 

Arc Flash Clothing & Protection For Safe Windfarm & Wind Turbine Working

Arc Flash Clothing & Protection

• uploaded by Chris Dodds - Thorne & Derrick Sales & Marketing Manager

Arc flash

Arc flash accidents are not nearly as rare as you would think and the hazards they create are severe. In wind turbines, these hazards are magnified. 

Installing and maintaining wind turbines can be a tricky job and it is important to understand the importance of staying safe and Protecting Lives by wearing arc flash clothing including an arc flash helmet, insulating boots and arc flash gloves.

In fact, most employers wouldn’t dream of permitting their teams on site without adequate protection and workers themselves are more than clued up when it comes to the latest electrical safety equipment requirements.

However, the same can’t be said when it comes to the potentially fatal risk posed by an Arc Flash – a relatively misunderstood, but extremely common type of electrical explosion facing those working on onshore or offshore, private or commercial wind turbine projects.

Arc Myth Busted: Did you know most arc flash accidents occur in LV systems?

Especially legacy switchgear and switchboards undergoing the The Three R’s – retrofit, refurbishment or repair. Modern technology Low, Medium & High Voltage Electrical Equipment with integral insulated arc-free busbar assemblies, arc flash relays and arc quenching switchgear, such as manufactured by Eaton, minimises but does not eliminate the risk of arc flash completely.

Of course, the best way to avoid arc flash is to de-energise – nevertheless, Arc Flash can occur on power systems inadvertently made live while undergoing maintenance under planned isolation procedures.

Image: Safety Management Services, Inc.

A Wind Turbine Arc Flash Incident

The Clear & Present Danger

Although no injuries were reported – thankfully – the devastation inflicted to the wind turbine pictured below is extreme, to the point of destruction. That turbine is beyond repair.

Now imagine just for a moment if the wind turbine had been manned or the incident had involved manpower – the feasibility of providing urgent medical treatment to an injured worker in a nacelle at high level is complicated. Often, the physical workplace location of the wind turbine prevents rapid rescue and emergency intervention due to remoteness and accessibility –  quite often offshore. By September 2018, the UK wind power sector consisted of 9,088 wind turbines with a total installed capacity of over 20.1 gigawatts: 12,222 megawatts of onshore capacity and 7,907 megawatts of offshore capacity.

Technicians from Vestas, the company that oversees the maintenance of the turbine, attended site in April 2018 to complete a damage assessment. An expert from the company, who specialises in examining wind turbines that have experienced major malfunctions and fires, began an investigation into how the fire occurred.

An engineer hired as part of the insurance claim eligibility process was able to look at the wind turbine and investigate the cause of the fire. According to the engineer’s findings, the turbine experienced an arc flash that caused an electrical fire.

Officials with Vestas have declared the nacelle a total loss, though the tower and foundation are reusable, and will be providing the client with the costs for options ranging from decommissioning of the wind turbine to replacement of the unit.

Clean-up at the site to remove the damaged nacelle occured over the summer but is not expected to be completed before the end of the year.

So don’t ignore The Arc – a few attributable costs of arc flash induced outages and downtime:

• Revenue loss incurred from inability to generate electricity. £100K’s-ish. Minimum.
• Outage period until repairs are complete. Weeks? Months??
• Replacement of damaged or destroyed equipment. Financially, don’t think about it.
• Consequential reputation damage. Immeasurable.

Image: Crown Estates

What Is An Arc Flash?

Hotter than the sun (around 20,000°C) and louder than a bullet, an Arc Flash is when an arcing fault releases dangerous levels of radiant energy, which vaporises metal that spews from the arc. The air is super-heated causing pressure waves that can propel individuals across rooms and create a deadly molten shrapnel.

It goes without saying; the extreme temperatures of an Arc Flash can burn clothing and human skin within fractions of a second, even if the operative is situated five or six metres away from the Arc Flash event. It can also result in an explosive pressure wave that can throw workers across the room and a sound blast that can rupture eardrums.

An Arc Flash event is also accompanied by a bright flash which can cause temporary or even permanent blindness.

Treatment for those that survive an incident can require years of skin grafts, hospital stays and rehabilitation – they may never recover sufficiently to regain their lifestyle, so it’s safe to say that choosing the appropriate PPE is key when it comes to Arc Flash safety.

Posing A Risk

Electrical in nature, Arc Flash poses a substantial risk to those working in the wind industry which is constantly growing in importance due to its potential to contribute significantly to our national energy needs.

When working on wind turbines or windfarms, Arc Flash incidents can occur in both low voltage environments as well as high voltage, with particular reference to the following incidents…

• Opening energised electrical cabinets and verifying zero energy (testing dead)
• Securing and removing lock out and tag out (LOTO) devices
• Conducting trouble shooting on energised equipment and parts
• Working on near or exposed live conductors
• Breaking ground to install turbines

It is worth noting that the above incidents are of broadly the same severity whether the turbine is part of a large commercial windfarm or one of the growing number of small scale turbines installed by businesses.

How To Protect Yourself Against Arc Flash

Arc Flash protection is found in specialist clothing and garments for “head-to-toe” protection – everything from arc flash coveralls to arc flash trousers.

Enhanced and effective arc flash protection is safely achieved by wearing layers of protective clothing and garments manufactured from inherent fibres and which feature specific Arc Flash resilient components. Without the correct high-quality garments, arc protection levels will be compromised.

In addition to quality, it’s important to consider the longevity of the garment – depending on how it’s manufactured it may lose its effectiveness. Always look for products that feature Arc Flash protective qualities in the thread, as opposed to just a sprayed material, which will lose its impact over time.

Arc Flash Risks & How To Prevent Them – Wind Turbines & Windfarms

Overview of Arc Flash Clothing | Contact us to discuss your garment and PPE requirements, we can mitigate risk with guidance on safe working practices and by providing appropriate worker clothing that offers advanced Arc Flash Protection that saves lives every day. Whether working on underground cables or overhead lines, here is a selection of workwear clothing – contact us to discuss your requirements;

ProGARM 4690 Coverall	ProGARM 4616 Trouser	ProGARM 5816 Trouser	ProGARM 7638 Trouser	ProGARM 6458 Coverall
ProGARM 7418 Trouser	ProGARM 7480 Coverall	ProGARM 5290 Polo Shirt	ProGARM 6444 Coverall	ProGARM 5286 Polo Shirt

>> Download Your Guide To Here <<

HV Cable Joints, Terminations & Connectors | Approved Stockists & Distributors | 3M Electrical (Cold Shrink) | Nexans (Euromold JTS MONO) | Pfisterer (CONNEX SEANEX) | 11kV 33kV 66kV Medium & High Voltage Cable Accessories

Static Discharge Sticks 33kV – CATU CM-50 Medium Voltage Static Ground Discharge Stick

CATU CM-50 Medium Voltage Static Ground Discharger

• uploaded by Chris Dodds - Thorne & Derrick Sales & Marketing Manager

Static Discharge Sticks

Product Launch – MV Medium Voltage Static Ground Discharge Stick

Thorne & Derrick supply the CATU CM-50 Static Discharge Stick used for medium/ high voltage overhead lines, busbars and substation use up to 33kV. The CATU discharge stick complies to the IEC 60855 standard and is used to safely dissipate electrostatic charges.

♦ IEC 60855-1:2016 Standard | Live Working – Insulating foam-filled tubes and solid rods. Part 1: Tubes and rods of a circular cross-section.

CATU CM-50 static discharge stick is an insulating orange tube with a diameter of 39mm and made of epoxy fibreglass – equipped with 6 metre of copper cable, cross section section 6sqmm, PVC insulated.

Static discharge sticks are designed to safely remove the static charge after de-energising of medium/high voltage power systems – this includes draining voltage retaining components before maintenance work is performed up to 33kV. The discharge sticks are equipped with hand guard and grip protection with sufficient electrical safety clearance against physical contact with medium/high voltages.

Static discharge sticks are available for higher voltage applications – contact us to discuss your MV HV EHV Electrical Safety Equipment requirements. 

IEC 60855 | Discharge Sticks for Medium Voltage Substations

Catu CM-50 Static Discharge Stick Specification

T&D are the UK’s largest stockis of CATU Electrical Safety Equipment of products for underground, overhead line and substation safety at LV, MV and HV cable networks.

Insulating Gloves | Insulating Matting | Voltage Detectors | Arc Flash Clothing | Substation Safety | Portable Earthing LV MV HV