Blog

Secure Spiking of Underground LV & HV Cables | Hydraulic Cable Spiking & Cutting Tools

PICOUP 250 Hydraulic Spiking and Cutting Tool | Stocked in the UK by Thorne & Derrick | Cable Spikers

Hydraulic Cable Spiking & Cutting Tools

Spiking Cable | Check Voltage Absence on LV & HV Power Cables

The PICOUP 250 and PICOUP 400 2 in 1 hydraulic cable spiking and cable cutting tools are used to check for and ensure the absence of voltage on LV MV HV underground power cables.

After the cable spiking process is complete, these PICOUP tools supplied by Thorne & Derrick can also be used to cut the cable. These tools offer total security to the user during application according to NFC 18510 standards.

Cable Spiking Tool Features

• 2 actions combined into one single tool (spiking and cutting)
• Enables the user to limit any resulting short circuit to a single-phase / ground fault when spiking multi-core cables. This cause any protective devices to trip before a 2 or 3 phases fault can be created
• In the event of spiking a live cable, the spiking blade can be replaced easily (minimising cost impact)
• No physical connection between the tool and the user
• Damage to infrastructure is minimised when spiking as a single phase to earth fault is created using a dedicated, local 70mm² copper earthing cable
• Cutting failure sensor
• Indication on the remote at the end of cutting operation
• Hydraulic over-pressure safety valve
• Battery charge status indicator
• Prevents the start of cutting if the battery is low
• MOS INDUSTRIE : 20 years of expertise

PICOUP 250 Hydraulic Spiking & Cutting Tool

The PICOUP 250 hydraulic spiking and cutting tool is supplied with flexible copper cable and earthing rod, two 24V batteries and quick charger, blade removal tool, 1 spare spike, two 2m straps for gallery work, a flash protection mat, a heavy duty waterproof case with carrying strap and laminated operating instructions.

PICOUP 400 Hydraulic Cable Spiking & Cutting Tool

PICOUP 400 Hydraulic Spiking & Cutting Tool

The PICOUP 400 hydraulic cable spiking and cable cutting tool is supplied with flexible copper cable and earthing rod, two 24V batteries and quick charger, blade removal tool, 1 spare spike, two 2m straps for gallery work, a flash protection mat, a heavy duty waterproof case with carrying strap and laminated operating instructions.

PB WEIR – DISTRIBUTORS, STOCKISTS & SUPPLIERS

PB Weir Substation Earthing and Transmission Line Earthing Equipment include line end clamps, earth end clamps, portable earthing leads and operating poles for high voltage substations, overhead power line and transmission line applications – voltages include 11kV, 33kV, 66kV, 132kV up to 400kV.

Thorne & Derrick provide competitive prices and fast delivery from stock for the complete range of PB Weir substation earthing and transmission line earthing equipment.

In 2018 In 2018 PB Weir joined the Novarc group and re-branded as PBwel and now, through the ESP group of companies, we are able to supply, support and maintain a comprehensive range of Electrical Safety Equipment which includes: Earthing, Insulated Tools, Arc Flash Protection, Personal Voltage Detection Helmets, Insulating Gloves, Voltage Detection, Operating Poles & Lock-Out Tag-out.

ALADIN | Improved electrical safety levels for workers operating near live equipment

➡ Read More Here: ALADIN Individual Voltage Alarm With Headlamp For MV Overhead Lines 10-69kV

Further Reading

• HV Cable Jointing Preparation Using Cable Spiking Gun
• Cable Spiking High Voltage Cables – UK Power Networks
• Cable Pull Calculations – Installing & Pulling Heavy Cables

LV, MV & HV JOINTING, EARTHING, SUBSTATION & ELECTRICAL EQPT

Thorne & Derrick International are specialist distributors of LV, MV & HV Cable Installation, Jointing, Duct Sealing, Substation & Electrical Equipment – servicing UK and global businesses involved in cable installations, cable jointing, substation, overhead line and electrical construction at LV, 11kV, 33kV and EHV.

Cut Cables, Crimp Lugs & Punch Boxes | RIDGID RE 60 Electrical Tool

RIDGID RE 60

3-in-1 Electrical Tool

Now there’s a more efficient way to cut, crimp, and punch on the jobsite. The new line of RIDGID electrical tools, the RE 60, features the unique QuickChange System, allowing you to quickly and easily switch between interchangeable heads for cutting, crimping and punching. Now your important tasks can be accomplished with one innovative tool.

Whether you are cutting wire, crimping lugs or punching boxes, the RE 60 helps you to maximize productivity and efficiency on the jobsite. Your most critical electrical tasks are brought together in one convenient tool.

RIDGID RE 60 features a 6-ton (60 kN) hydraulic force output to cut armoured cable up to 50 mm O.D., crimp Cu/Alu cable lugs up to 300 mm² and punch round holes up to 63,5 mm. During cutting and crimping, the ram will automatically retract once the cycle is completed. Punching applications require use of the release trigger.

The built-in sensors and LED indicators ensure tool performance, allow the tool to operate in extreme temperatures (-10° -50°C), monitor cycle time, generated pressure, battery life and indicate when the tool requires service.

---

RIDGID RE 60 TOOL

Features

• 60 kN force output for crimping lugs up to 300 mm², cutting cables up to 50 mm diameter and punching holes up to 3 mm mild steel.
• Automatic ram retraction when cutting and crimping
• Longest service interval in the industry (32.000 cycles)
• 360° head rotation
• Bright white LED for illuminating the workspace
• Rubber over-molded grip for superior comfort and control
• Nylon straps for greater tool security
• Heavy-duty, blow-molded case for easy transport and storage
• On/Off button for disabling tool when changing dies or heads
• Powered by the RIDGID 18V Advanced Lithium battery platform

RIDGID RE 60 Featuring the RIDGID QuickChange System

---

RIDGID RE 60 TOOL

Specifications

Order Code	RIDGID RE 60
Manufacturer	RIDGID Tools
Description	RE 60 Electrical Tool Kit w/SC-60B Scissor Cutter, LR-60B Latching Round Crimp Head and PH-60B Punch Head
Approximate Cycle Time	5 seconds
Service Interval	32,000 cycles
Weight	3.2 kgs w/battery

RIDGID RE 60 3-in-1 Electrical Tool

---

See how T&D support, supply and service the Renewable Energy industry.

Thorne & Derrick are Specialist Distributors to the UK and international Offshore Wind & Renewable industry to provide safe and reliable LV HV Electrical Cable & Power Distribution Systems up to 66kV – we are highly customer responsive and absolutely committed to providing a world-class service.

Contact our UK Power Team for competitive quotations, fast delivery from stock and technical support or training on all LV-HV products.

Stockists & Suppliers of Cable Cutting & Crimping Tools manufactured by Klauke and Cembre.

Key Product Categories: Duct Seals | Cable Cleats | Cable Glands | Electrical Safety | Arc Flash Protection | Cable Jointing Tools | Cable Pulling | Earthing | Feeder Pillars | Cable Joints LV | Joints & Terminations MV HV 

Arc Flash Garments & Clothing | The Top 10 Sellers

Stockists | Suppliers | Distributors

Arc Flash Protection

Thorne & Derrick distribute the most extensive range of Low & High Voltage Cable Installation & Electrical Distribution Equipment to the Power Transmission & Distribution industry in the onshore and offshore wind, solar, rail, oil/gas, data centre, battery storage and utility sectors – this includes Arc Flash Garments & Clothing to provide protection against the dangers of arc flash risks to workers carrying out maintenance, inspection and repair on electrical power systems.

We service UK and international clients working on underground and subsea cables, overhead lines, substations and electrical construction at LV, 11kV/33kV up to EHV transmission and distribution voltages.

The following items comprise the current Top 10 Sellers from our extensive ProGARM range of Arc & Electrical PPE for arc flash and flame resistant protection of utility workers.

ProGARM 4690 Coverall	ProGARM 4616 Trouser	ProGARM 5816 Trouser	ProGARM 7638 Trouser	ProGARM 6458 Coverall
ProGARM 7418 Trouser	ProGARM 7480 Coverall	ProGARM 5290 Polo Shirt	ProGARM 6444 Coverall	ProGARM 5286 Polo Shirt

>> Download Your Guide To Here <<

HV Cable Joints, Terminations & Connectors | Approved Stockists & Distributors | 3M Electrical (Cold Shrink) | Nexans (Euromold JTS MONO) | Pfisterer (CONNEX SEANEX) | 11kV 33kV 66kV Medium & High Voltage Cable Accessories

Nofirno Sealing System Successfully Tested for Use in Explosive Environments

Nofirno

NOFIRNO systems are used to seal cable ducts in an extensive range of Process industry sectors including the fine and speciality chemicals, petrochemicals, pharmaceuticals, hydrogen and polymers manufacturing sectors. The NOFIRNO range of duct seals are used to protect against water ingress, gas migration, fire spread and rodent infestation into electrical substations and buildings through LV MV HV cable ducting systems.

ATEX directive requirements can be imposed for specific uses in hazardous area locations (Zone 1/2 Flammable Gas & Zone 21/22 Combustible Dust) where there is a potential risk of explosion. Kiwa has thus investigated the extent to which the NOFIRNO sealing system (from Beele Engineering) fulfils ATEX directive 2014/34/EU.

Comprised of rubber and filler sleeves and sealant, the system is used to treat transit openings for cables and pipes in walls, floors, bulkheads or decks, so that they are fire-resistant and sealed against gas, smoke and water. Kiwa’s research has shown that NOFIRNO is extremely suitable for use in environments such as those covered by the ATEX directive and described in the European standard EN 1127-1 ‘Explosive atmospheres – Explosion prevention and protection – Part 1: Basic concepts and methodology’.

Because the NOFIRNO sealant, NOFIRNO rubber sleeves and the complete NOFIRNO sealing system do not fulfil an autonomous role and are not equipment in the sense of the ATEX directive, the risk evaluation focused on use of the NOFIRNO in cable and pipe transits. All possible ignition sources related to the sealing system were also investigated.

Among the possible ignition sources which were assessed, were hot surfaces, flames and hot gases (including hot particles), mechanically-generated sparks, electrical equipment and power leakages, cathodic corrosion protection, static electricity, lightning, electromagnetic and ionising radiation, ultrasonic sound waves, adiabatic compression and shockwaves and exothermic reactions, including materials self-igniting.

Kiwa concluded that for all hazardous situations as described in EN 1127-1, there is no ignition source for NOFIRNO sealant, NOFIRNO rubber sleeves, NOFIRNO rubber filling sleeves and the complete, installed NOFIRNO system.

CSD NOFIRNO DUCT SEAL SYSTEM

Watertight, Gastight & Fire Protection & Sealing for Cables & Duct Entries

CSD NOFIRNO duct seals is a multi-cable and pipe transit sealing system designed specifically for cable duct seals and building entries providing an effective and simple solution protecting against flood water and gas ingress.

NOFIRNO duct seals consist of rubber multi sleeves which are in bonded strips of 10 sleeves and a high quality silicone based sealant which are quicker and easier to install than the CSD standard RISE duct seals.

The bonded sleeves can be easily torn off for filling smaller gaps and using cutting tool sleeves can be quickly slit to allow fitting around cables ensuring cable separation – NOFIRNO duct seals are also used to pack the free space, providing a backing for the application of the cable sealant.

Completing the seal with a 20mm layer of NOFIRNO sealant will provide a technically advanced and high performance duct seal. View the complete range of CSD Sealing Systems to protect against damage caused by water ingress, gas spread or fire/flame to cables and ducts.

Should you require any assistance with the safe and effective sealing of cables and pipe systems to ensure DSEAR | ATEX Regulatory Compliance please do not hesitate to contact Thorne & Derrick.

Duct Seals | Watertight | Gastight | Fire Resistant | Resist Rodents | Cables LV MV HV

Thorne & Derrick are Specialist Distributors to the Process Industries – we supply and support businesses working on the design, construction and maintenance of UK, European and international projects.

We can competently specify and competitively supply an extensive range of Hazardous Area Equipment (ATEX & IECEx) to provide Power, Heating & Lighting to the Explosive Atmospheres industries – this includes LV HV Cables, Accessories Jointing, Substation & Electrical Eqpt from 600V to 132kV.

Based in the UK, we are highly customer responsive and absolutely committed to providing a world-class service.

Since 1985, we have provided expert technical support and express delivery from extensive UK stocks to world-wide destinations.

Cut, Crimp & Punch | Universal Tool with Triple Function Tool | Klauke EK 120 UNV

Klauke EK 120 UNV Tool

A Universal Tool For Cable Cutting, Crimping & Hole Punching Panels

The EK 120 UNV is a 3-in-1 Universal Tool manufactured by Klauke for crimping, cutting and punching cables. Klauke EK 120 UNV crimps cables up to 400mm², cuts up to 40mm outside diameter and punches up to 144mm holes.

This universal battery powered, hydraulic tool has one head for cable crimping, cutting and hole-punching making it ideal for use in the assembly field where all common worktasks can be carried out by the electrical engineer, jointer or installer using just the one tool. All tool data can be viewed via the display and i-press® app.

Tool Features

• Choose your battery system: Bosch or Makita
• All data can be easily read via Bluetooth
• Universal tool head flip top style, rotatable
• Simple and safe tool: One-button operating concept for controlling all tool functions
• Effortless working due to balanced centre of gravity
• LED for work area illumination
• 2-stage hydraulic system with fast feed and power stroke
• Simple and safe: Automatic retraction after operation completed (crimping or cutting)
• Always ready-to-use thanks to battery charge and service display

Klauke EK 120 UNV Specifications

Further Reading

Review other Blogs in this series of articles about Cable Lugs, Crimping Cables & Tools:

• Cable Lugs – Crimping Applications & Standards
• Copper Cable Lugs For Special Applications
• Indent Crimping Of Cables – Benefits & Limitations
• Cable Lugs & Crimping Using The Hexagonal Crimp Method
• DIN Standard – Crimping & Compressing Aluminium Cable Lugs & Connectors
• Copper & Aluminium – Crimping CU-AL Cables
• Electrically Driven Crimping Tools For High Volume Applications

Klauke EK 120 UNV Battery-powered hydraulic universal tool 10 – 400 mm²

LV MV HV Jointing, Earthing, Substation & Electrical Eqpt

Crimping Cables, Lugs & Tools

Thorne & Derrick distribute Cable Lugs & Cable Connectors to terminate, splice and joint LV MV HV cables – this includes copper, aluminium and bi-metallic connectors and a complete range of crimping tools for specific use on all Low, Medium & High Voltage cable types.

➡ Associated Brands & Products | Klauke | Cembre | Pfisterer Sicon | Cable Crimping & Cable Cutting Tools

Klauke Cable Crimping & Cutting Tools | the world‘s first battery hydraulic crimping and cable cutting tools with Tri-Insulation Barrier technology that provides users with 1000V protection against electrical shocks.